Member name: Steve
From: Wisconsin
Photos: Steve has not uploaded any photos
Joined: Tue Apr 29 13:38:38 2008
Profile updated: Tue Apr 29 13:38:38 2008
Contact: [please login to contact this member]
Steve has posted 7 messages and replied to 13 messages.
|
| List of 100 most recent messages and comments- Mon Jun 30 09:40:50 2008:
Fanuc_Default_G_codes CommentIs it giving you an alarm? Are you sure you have MacroB on your control? Check parameter 913 bit 7. Couple things I... 200. Also about 8 lines down in N2 you have YO.0873. that is the letter O in there should be a zero. "Y0.0873".... - Thu Jun 26 15:30:06 2008:
Okuma_vertical_mc_6_vae CommentSee if there is a overtravel release or bypass button on the operator panel. If so hold it in while you handle or jog... will wire in a bypass switch in or on the control panel that you can flip and then the axis will move off the switch.... - Wed Jun 25 08:42:30 2008:
FANUC_OM_Controller_Program_load CommentTo load and unload 9000 programs there is a parameter that write protects these programs. I do not have a OM control... PORT SETTINGS, ADVANCED, set the FIFO to it's lowest setting, and click ok when exiting all menus.Good luck!... - Mon Jun 16 15:02:55 2008:
Seicos MIII Alarm 2AC5 MessageIt is a HItachi Seiki VK55II VMC with Seicos MIII control. There was a power outage. Now at power up there is alarm... APC Slave Unit Has Been Blown. I can not seem to find anything on this. Has anyone seen this? Thanks for your help!!... - Thu Jun 12 07:58:08 2008:
custom_macros CommentI didn't know that. Thanks for the tip... didn't know that. Thanks for the tip Wilbur... - Wed Jun 11 07:42:01 2008:
custom_macros CommentJ.K my apologize but this forum only allows 24 charters in one word so I had to add a space in the website addresses I... add a space in the website addresses I gave you. Take the space between n and s in the first and i and n in the second.... - Wed Jun 11 07:37:13 2008:
custom_macros Comment-Joe he's asking for the custom macro "program" not how to do a tool change.-J.K. You will probably have to contact... 2 minutes. www.gefanuc.bn si.net/eforum/index.php www.practicalmachi nist.com/vb/index.php www.cnczone.com/ ... - Mon Jun 9 12:15:54 2008:
detailed_notes_of_custom_macro_programming CommentMost of the learning of using macro's is by doing. I will try and compile all my notes that have some detail. A quick... FEEL FREE TO ASK QUESTIONS AS YOU ARE TRYING DIFFERENT PROGRAMS. I WILL TRY TO ANSWER TO THE BEST OF MY ABILITY.... - Mon Jun 9 08:14:33 2008:
Fanuc_15_M CommentGunsSounds like your subroutines are probably 8000 & 9000 program numbers. You have to go to settings PWE parameter... 9000 programs then should be able to load. If it is 8000 program numbers then it is parameter 11 bit 0 set equal to 0.... - Wed Jun 4 16:42:50 2008:
writing_programs CommentTo all, The format I have won't work to post, but I have a good example of VMC drilling of a simple part. If you... Macro Programming, which if you request I will write up some examples and send them off. Best of luck, Steve... - Tue May 27 15:41:44 2008:
Machine tool builders MessageDoes anyone know of a good website or research area for comparing machinery? We were looking at purchasing some new... Fanuc Oi control I mainly used 15 and 18 controls; any insight would be greatly appreciated!Thanks for the help. ... - Thu May 22 16:44:01 2008:
Fanuc_15MF_VMC_turn_table CommentNo worries guys I found the settings. FYI Parameter 1007 bit 5 will rotate the table in the direction that minimizes... 360 deg. when jogging the the table around past 360 allowing the homing of the C-axis to be less then 1 revolution.... - Thu May 22 11:21:54 2008:
Fanuc 15MF VMC turn table MessageI am programming a Monarch RTB-X VMC with C-axis turn table and a Fanuc 15MF control. When indicating a part in table... around -350deg to reach 0 instead of shortest distance +10deg would be C0. Please advise.Thanks for the help!! ... - Fri May 16 09:35:54 2008:
Fanuc_Default_G_codes CommentWhat?? Would you please elaborate on... Would you please elaborate on that?... - Thu May 15 11:03:36 2008:
Fanuc Default G-codes MessageDoes anyone know how to change the default G-codes for after resetting or power up. It is a Fanuc 15TA control using... in feed per revolution or constant surface speed. Just a simple F.02 S250 and away you go.Thanks for your help. ... - Fri May 9 08:15:23 2008:
Fanuc 15TA memory expansion backup MessageI am purchasing memory expansion and macro variable extension from Fanuc. I want to be sure exactly what I need to back... this need to be done and how is this done? Is there anything that I am missing?? Please advise. Thanks for the help!... - Fri May 2 10:32:36 2008:
memory expansion MessageI want to expand the memory on our Fanuc 15T & 15TA from 320M memory to 1280M memory with 1000 program numbers. Does... numbers. Does anyone know if hardware is required to do so? Or is it just the option that must be purchased from Fanuc?... - Thu May 1 16:39:33 2008:
120405-Fanuc_15T_offset_parameters CommentI did not want to have to write a program to loop through every tool change but this is the only way I see capturing... will grab the tool radius from offset page for offset 32)Thanks for all your help and responding.... - Thu May 1 13:00:40 2008:
120405-Fanuc_15T_offset_parameters CommentPlease advise. I am having no luck with the machine tool... advise. I am having no luck with the machine tool builder.... - Tue Apr 29 13:41:33 2008:
Fanuc 15T offset parameters MessageI am programming a Fanuc 15T control on a VTL. There is no preset relation between a T-code and a tool offset. This is... to current tool but when programming for example #30=#[#4120+2900.] alarm variable out of range arises. Please advise....
|
|
Login or Register
Top Searches: • www gefanuc bn si net 2feforum 2findex php • fanuc oi macro programming • |