Deepak Bodhani profile

Manufacturer & supplier of wired & wireless DNC Systems, CNC Code Loader, Ethernet-RS232 Converters, RS-232 Isolators, Machine Monitoring Systems since 1990 in India

• Fri Feb 1 07:58:05 2008:
  PS_ALARM_87 Comment

  Alarm 87 means RS-232 failure.

  Refer FANUC Manual for detailed... 87 means RS-232 failure.

  Refer FANUC Manual for detailed meaning.

  Deepak

  ...

• Wed Jan 30 06:15:49 2008:
  WirelessDNC on HAAS Message

  We offer wireless DNC for HAAS with drip feed mode. contact on my e-mail if... offer wireless DNC for HAAS with drip feed mode. contact on my e-mail if interested....

• Wed Jan 30 05:58:43 2008:
  Fanuc_15_M Comment

  Dear Friends,

  We have a portable terminal called DIGI-HHT / LK which helps in taking all your CNC program files, NC... rectification, you can re-load all data back to FANUC in no time, via RS-232 port. Read more at digitech-engineers.com...

• Wed Jan 30 05:47:37 2008:
  Fanuc_21i_TA_Memory_Upgrade Comment

  Dear Craige,

  We offer portable CNC code Loader of 128 KB memory. It is to be hooked to RS-232 port of FANUC. You... are working in India. See more info. on our web site digitech-engineers.com & revert back to me on digitech@vsnl.com...

• Wed Jan 30 05:27:12 2008:
  File_Structure Comment

  You can also get automatic log file of all DNC transactions, along with date, time & file name with path. Hence... other as SHOP. MASTER folder will only send the files to CNC. The SHOP folder will only receive the files from CNC....

• Wed Jan 30 05:19:34 2008:
  File_Structure Comment

  Our WIN-COM DNC Software allow you to define three folders on your DNC-PC. One folder for the files, receiving from... CNC. The CNC user can access them from his CNC key-pad. You can get more info at our web site, digitech-engineers.com...

• Wed Jan 30 05:10:02 2008:
  Hartford Comment

  Use our DNC Software. Write to me on digitech@vsnl.com

  Also see more info at... our DNC Software. Write to me on digitech@vsnl.com

  Also see more info at digitech-engineers.com...

• Wed Jan 30 05:07:26 2008:
  Dnc_problem_for_Mitsubishi_Meldas_520AM Comment

  Use our DNC Software. email me on digitech@vsnl.com. Also see more information at digitech-engineers.com

  Set...

  Set parameter no. 8109 as 1 on Mitsubishi.

  Use Xon-X-off for hand shaking. It should work well. - Deepak

  ...

• Wed Jan 30 04:59:11 2008:
  PS_ALARM_87 Comment

  You must use RTS & CTS signals on FANUC side as hardware hand shake. Also Pin No. 6, 8, & 20 must be shorted at Fanuc... Pin No. 6, 8, & 20 must be shorted at Fanuc side. Even if the problem is observed, reduce the baud rate & see. - Deepak...

• Wed Jan 30 04:54:13 2008:
  DNC_Direct_Numerical_Control Comment

  You will get lot of technical information on wired & wireless DNC at digitech-engineers.com. You can have Ethernet... based CNC Networking, Wireless LAN based CNC Networking, or Industrial Bluetooth based CNC Networking - Deepak

  ...

• Wed Jan 30 04:45:06 2008:
  Dnc_link Comment

  Mike,

  I agree with Dan. If you are using opto-isolator in between, I have seen some Opto-Isolator do not respond at... The shield wire to be connected to pin 7 (Ground) at CNC side. It helps in reducing the electrical noise.

  - Deepak...

• Wed Jan 30 04:29:10 2008:
  CMT Protocol of Mazak Message

  Facing a problem when connect wireless DNC to Mazak T Plus with CMT Protocol. Work well with wired DNC.

  Reply... when connect wireless DNC to Mazak T Plus with CMT Protocol. Work well with wired DNC.

  Reply digitech@vsnl.com

  ...

• Wed Jan 30 04:25:28 2008:
  Wireless DNC on Mazak T Plus Message

  Has any one used wireless DNC on Mazak T Plus with CMT Protocol ? Reply... any one used wireless DNC on Mazak T Plus with CMT Protocol ? Reply digitech@vsnl.com...